SINTESIS DAN KARAKTERISASI NANOPARTIKEL OKSIDA BESI MENGGUNAKAN METODE BALL MILLING DAN KOPRESIPITASI
Abstract
This Research has carried out on natural sand originating from the Rokan river, Riau Province by converting it into magnetic iron oxide nanoparticles to determine changes in magnetic properties and particle size. Natural sand samples of the Rokan river were separated between magnetic and non-magnetic particles using an iron sand separator (ISS). ISS products are further synthesized using ball milling and coprecipitation methods. 70-hour ball milling products, coprecipitation without ball milling and coprecipitation with 70-hour ball milling are then given NdFeB (neodymium iron boron) magnets to clean impurities containing non-magnetic elements. The results of this study showed that the highest magnetic acceptability value was obtained in coprecipitation products with ball milling, which was 12.9 × 10-2. This is because coprecipitation products have an abundant content of chemicals in the form of magnetic elements. Based on the results of chemical composition testing using X-ray flourescence (XRF) it was found that in coprecipitation products with ball milling there was 64.504% iron (Fe) content, while 70-hour ball milling products and coprecipitation without ball milling the percentage of Fe protection was 15.023% and 54.152%, respectively. Based on the results of the identification of the chemical composition in the sample, coprecipitation products with 70-hour ball milling have high magnetic induction values and magnetic suseptibility caused by the magnetic content in products such as Fe which are very high and non-magnetic content is very low such as Si compared to 70-hour ball milling products and coprecipitation products without ball milling.
Keywords
Full Text:
PDF (Bahasa Indonesia)References
1. Nengsih, S. (2018). Potensi nanopartikel magnetit pasir besi Lampanah Aceh Besar melalui studi kajian teknik pengolahan, sintesis dan karakteristik struktur. CIRCUIT: Jurnal Ilmiah Pendidikan Teknik Elektro, 2(1).
2. Purwanto, S., & Dani, M. (2017). Strukturmikro dan Sifat Magnet Pasir Besi Pasca Ultrasonifikasi. Jurnal Sains Materi Indonesia, 19(1), 14-18.
3. Tebriani, S. (2019). Analisis Vibrating Sample Magnetometer (VSM) pada Hasil Elektrodeposisi Lapisan Tipis Magnetite Menggunakan Aruscontinue Direct Current. Natural Science Journal, 5(1), 724-725.
4. Burmeister, C. F., & Kwade, A. (2013). Process engineering with planetary ball mills. Chemical Society Reviews, 42(18), 7660-7667.
5. Ningsih, S. K. W. (2016). Sintesis Anorganik. Padang: UNP Press.
6. Aygar, G., Kaya, M., Özkan, N., Kocabıyık, S., & Volkan, M. (2015). Preparation of silica coated cobalt ferrite magnetic nanoparticles for the purification of histidine-tagged proteins. Journal of Physics and Chemistry of Solids, 87, 64-71.
7. Malvern, A. (2012). Basic Guide to Particle Characterisation. Malvern Instruments, Ltd.: Malvern, UK.
8. Wijayanto, S. O., & Bayuseno, A. P. (2013). Analisis kegagalan material pipa ferrule nickel alloy n06025 pada waste heat boiler akibat suhu tinggi berdasarkan pengujian: mikrografi dan kekerasan. Jurnal Teknik Mesin, 1(4), 33-39.
9. Alisna, S., & Sinuraya, S. (2021). Pemetaan Suseptibilitas Magnetik dan Penentuan Kandungan Logam pada Air Gambut di Kelurahan Tuah Madani Kecamatan Tampan Pekanbaru. Komunikasi Fisika Indonesia, 18(1), 12-17.
10. Sinuraya, S., Amiruddin, E., Nurrohmah, D., & Wulandari, T. (2021). Analisa Perubahan Suseptibilitas Magnetik dan Komposisi Partikel Pasir Alam Sungai Rokan Sebagai Fungsi Kecepatan Putar Tabung Ball Milling. Komunikasi Fisika Indonesia, 18(3), 225-229.
DOI: http://dx.doi.org/10.31258/jkfi.19.2.91-98
Refbacks
- There are currently no refbacks.
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
Indexing by:
